控制屋顶窗户的遮阳。
目录
输入↑
缩写 | 总结 | 描述 | 单元 | 数值范围 |
---|---|---|---|---|
Tg | Toggle | 在开、停、关之间切换。 用于单按键控制。 |
- | 0/1 |
Po | Partial open with push & hold | 通过推动&保持住实现部分开启 | - | 0/1 |
Pc | Partial close with push & hold | 通过推动&保持住实现部分关闭 | - | 0/1 |
Co | Complete open | 如果在运动中,则停止。 | - | 0/1 |
Cc | Complete close | 如果在运动中,则停止。 | - | 0/1 |
Dwc | Door/window contact | On 时,完全打开遮阳,并锁定该模块。 仍可以通过 App 进行手动控制。 |
- | 0/1 |
Wa | Wind alarm | 将遮阳移动到参数(Wap)设定的风暴预警位置,并锁定模块。用于风暴保护。风暴预警不是人工操作。 所连接的传感器名称在用户界面中使用的名称。 |
- | 0/1 |
Off | Off | 脉冲停止运动。On 时锁定模块。 主导性输入。 |
- | 0/1 |
Pos | Position of shading | 将遮阳移到指定的位置。 | % | 0...100 |
T5 | T5 control | 按键1:完全打开 按键4:完全关闭 |
- | ∞ |
DisPc | Disable periphery control | On 时停用输入 Tg、Po、Pc、Co、Cc、So、T5。(如童锁、清洁) 仍可以通过用户界面进行控制。 |
- | 0/1 |
So | Slightly open | 软百叶窗完全关闭,并根据参数(Rd)在水平位置移动板条。 卷帘、窗帘和遮阳篷根据参数(Rd)移动到位置。 |
- | 0/1 |
Sps | Sun position automatic start | Activates the sun position automatic when On at the beginning of the shading period, or also with a pulse during the shading period. The sun position automatic is deactivated for the rest of the day, if block is operated manually. Pulse on (Spr) followed by a rising edge on (Sps) or pulse on (Spr) while (Sps) is active, restarts the sun position automatic. |
- | 0/1 |
DisSp | Disable sun position automatic | On 时,停用“太阳位置自动”。 | - | 0/1 |
Spr | Sun position automatic restart | Pulse followed by a rising edge at input (Sps) or pulse while input (Sps) is active, restarts the sun position automatic. | - | 0/1 |
输出↑
缩写 | 总结 | 描述 | 数值范围 |
---|---|---|---|
Op | Open | 打开 此输出仅在某些配置中可见。 |
0/1 |
Cl | Close | 关闭 此输出仅在某些配置中可见。 |
0/1 |
Pos | Position of shading | 遮阳的位置(0.0 = 打开,1.0 = 关闭) | 0...1 |
Wds | Wind, door/window contact state | 当模块或关联的中央模块的输入(Wa)激活时,或当输入(Dwc)激活时,为 On。 | 0/1 |
Off | Off | 当输入(Off)为1时激活。 | 0/1 |
Sp | Sun position automatic | On,如果输入(Sps) = 1且输入(DisSp)=0...并且如果勾选了 "使用阳光 "的设置,并且阳光晴朗。 或者在应用程序中打开了基于太阳位置的自动化。 |
0/1 |
AC | API Connector | 基于 API 的智能连接端口。 API Commands |
- |
参数↑
缩写 | 总结 | 描述 | 单元 | 数值范围 | 默认值 |
---|---|---|---|---|---|
Wap | Wind alarm position | 0 = 完全打开 1 = 完全关闭 |
- | 0/1 | 0 |
Opd | Opening duration | 开启时长 | s | 0...∞ | 75 |
Cld | Closing duration | 关闭时长 | s | 0...∞ | 75 |
Mld | Motor lock duration | 换向时的电机锁定时间。 | s | 0...∞ | 0,5 |
Tdc | Time double-click | 输入端(Po)、(Pc)上用于完全打开/关闭的双击时长。 0 = 不使用 |
s | 0...∞ | 0,3 |
Tlc | Time long-click | 在输入端(Po)、(Pc)上的长点击持续时间用于完全打开/关闭。 如果你喜欢双击,那么设置值>(Opd)或(Cld)。 0 = 总是开始完整的行程。 |
s | 0...∞ | 3 |
minTd | Minimum travel duration | 当脉冲触发输入(Po)或(Pc)时的最小行程时间。 | s | 0...∞ | 0,4 |
Spm | Sun position automatic mode | 0 = Automatic stays Off if shading is closed. If the input (Sps) is active, a pulse on (Spr) restarts the sun position automatic. 1 = Automatic always allowed. |
- | 0...1 | 1 |
Spe | Sun position automatic end action | 0 = 没有动作 1 = 完全打开 2 = 完全关闭 |
- | 0...2 | 1 |
Dir | Compass direction | 窗口的指南针方向: 0=北 90=东 180=南 270=西 -1=未配置 |
° | -1...359 | -1 |
Dts | Direction tolerance start | 当太阳进入遮阳区域时,用于“太阳位置自动”的方向公差。 | ° | 0...90 | 85 |
Dte | Direction tolerance end | 当太阳离开遮阳区域时,用于“太阳位置自动”的方向公差。 | ° | 0...90 | 85 |
Pi | Pitch | 屋顶或窗户倾斜度。 0 = 水平 90 = 垂直 |
° | 0...90 | 30 |
Spos | Sun position automatic start offset | 相对于日出的“太阳位置自动”的起始偏移量。 | min | -90...90 | 30 |
Spoe | Sun position automatic end offset | 相对于日落的“太阳位置自动”的结束偏移量。 | min | -90...90 | -30 |
Sop | Slightly open position | 用于输入(So)和(Sps)的位置。 | % | 0...100 | 80 |
偏好↑
总结 | 描述 | 默认值 |
---|---|---|
使用阳光信息 | 只有当系统变量“阳光”和输入 Sps 处于激活状态时,才会激活自动遮阳。 | - |
方向参数↑
Dir: 遮阳设备相对于地理北方的指南针方向。(0=北,90=东,180=南,270=西)
Dts: 太阳进入遮阳设备时的方向公差。方向公差是相对于遮阳设备的垂直角度而言的。例如,考虑到建筑物的突起物。如果你的遮阳设备不受影响,你可以将其保持在默认值85º。
Dte: 太阳离开遮阳设备时的方向公差。方向公差是相对于遮阳设备的垂直角度而言的。例如,考虑到建筑物的突起物。如果你的遮阳设备不受影响,你可以将其保持在默认值85º。
起始/结束偏移量↑
有了参数(Spos),“太阳位置自动”将在日出后延迟这个分钟数。
这主要与那些可能在日出后不能立刻晒到太阳的窗口来说相关。
有了参数(Spoe),“太阳位置自动”将提前于日落前的这个分钟数。
这与日落前可能受到太阳影响的窗户有关。
这两个参数有两种可能的应用:
日出后和日落前,太阳往往被其他建筑、结构或树木遮挡。在这里,“太阳位置自动”的开始或结束时间可以被调整以适应这些。
另一种可能是改变时间,以便在遮阳打开时可以看到日出或日落。
通过用户界面启用昼夜节律↑
可通过用户界面手动启动昼夜节律功能,当 太阳位于窗户$时,百叶窗会自动降下。至于是晴天还是阴天,则不予考虑。
时刻表↑